{"titulo":"Catálogo Contadores Prepago","tipo":"archivo de consulta","productos":[{"id":8,"nombre":"ECO011AG ","referencia":"ECO011AG ","resumen":"Metro contador electrónico de energía, carril DIM, analógico, monofásico.\n\r\n(Corriente nominal a elegir dentro del producto)","descripcion":" Available as 35mm DIN standard rail mounted, conforming to Standards DIN EN 50022, as well as front PANEL mounted (the center distance between two mounting holes is 63mm or 67mm). Two mounted methods above are optional for user.\n 6 pole width (modulus 12.5mm), complying with Standards JB/T7121-1993.\n Can select the step motor impulse register of 5+1 digits (99999.1kWh) or 6+1 digits (999999.1kWh) LCD display.\n Can select two LCD displays with 6 digits, to show total power (5+1 digits display), and realtime power (4+2 digits display) which can be cleared by the red button on the nameplate. This red button can be protected by the seal and this model meter suits for the renting house.\n Can select the inside load switch for the remote control credit.\n Can select the inside far infrared data communication port and RS485 data communication port, the communication protocol complies with Standards DL/T645-1997, can also select the other communication protocol.\n Equipped with a polarity passive energy impulse output terminal, conforming to Standards IEC 62053-31 and DIN 43864.\n Two LEDs to indicate separately the power state (green) and the energy impulse signal (red).\n Measure the active energy consumption in one direction on single phase two wire, which is not related with the load current flow direction at all, complying with Standards IEC 62053-21.\n Direct connection for use. Two connections: type S and type T for option.\n The short terminal cover is made with the transparent PC, to reduce the installation space and is convenient for centralized installation.","caracteristicas":[{"name":"Corriente de arranque: ","value":" \t0.02 / 0.04 / 0.08 A (dependiendo de la corriente nominal seleccionada) "},{"name":"Corriente Nominal: ","value":"5(30) / 10(60) / 20(120) Seleccione "},{"name":"Metro Contador","value":"analógico de 5 + 1 dígitos"},{"name":"Prestaciones de aislamiento: ","value":"4 kV tensión de CA durante 1 minuto, de forma de onda de tensión de 6 kV 1.2/50us impulso. "},{"name":"Voltaje de Referencia: ","value":"230 V"}],"opciones":[{"name":"Corriente Nominal","value":"10 (60)A, con corriente de arranque 0.04 A"},{"name":"Corriente Nominal","value":"20 (120)A, con corriente de arranque 0.08"},{"name":"Corriente Nominal","value":"5 (30)A, con corriente de arranque 0.02"}],"imagenes":["../tienda/img/p/4/1/41.jpg"],"ficha":"index.php?producto=8"},{"id":9,"nombre":"ECO011GC","referencia":"ECO011GC","resumen":"Metro contador electrónico de energía, carril DIM, digital, monofásico.\n\r\n(Corriente nominal a elegir dentro del producto)","descripcion":" Available as 35mm DIN standard rail mounted, conforming to Standards DIN EN 50022, as well as front PANEL mounted (the center distance between two mounting holes is 63mm or 67mm). Two mounted methods above are optional for user.\n 6 pole width (modulus 12.5mm), complying with Standards JB/T7121-1993.\n Can select the step motor impulse register of 5+1 digits (99999.1kWh) or 6+1 digits (999999.1kWh) LCD display.\n Can select two LCD displays with 6 digits, to show total power (5+1 digits display), and realtime power (4+2 digits display) which can be cleared by the red button on the nameplate. This red button can be protected by the seal and this model meter suits for the renting house.\n Can select the inside load switch for the remote control credit.\n Can select the inside far infrared data communication port and RS485 data communication port, the communication protocol complies with Standards DL/T645-1997, can also select the other communication protocol.\n Equipped with a polarity passive energy impulse output terminal, conforming to Standards IEC 62053-31 and DIN 43864.\n Two LEDs to indicate separately the power state (green) and the energy impulse signal (red).\n Measure the active energy consumption in one direction on single phase two wire, which is not related with the load current flow direction at all, complying with Standards IEC 62053-21.\n Direct connection for use. Two connections: type S and type T for option.\n The short terminal cover is made with the transparent PC, to reduce the installation space and is convenient for centralized installation.","caracteristicas":[{"name":"Corriente de arranque: ","value":" \t0.02 / 0.04 / 0.08 A (dependiendo de la corriente nominal seleccionada) "},{"name":"Corriente Nominal: ","value":"5(30) / 10(60) / 20(120) Seleccione "},{"name":"Metro Contador","value":"digital de 6 + 1 dígitos LCD"},{"name":"Prestaciones de aislamiento: ","value":"4 kV tensión de CA durante 1 minuto, de forma de onda de tensión de 6 kV 1.2/50us impulso. "},{"name":"Voltaje de Referencia: ","value":"230 V"}],"opciones":[{"name":"Corriente Nominal","value":"10 (60)A, con corriente de arranque 0.04 A"},{"name":"Corriente Nominal","value":"20 (120)A, con corriente de arranque 0.08"},{"name":"Corriente Nominal","value":"5 (30)A, con corriente de arranque 0.02"}],"imagenes":["../tienda/img/p/4/2/42.jpg"],"ficha":"index.php?producto=9"},{"id":10,"nombre":"ECO011ZA","referencia":"ECO011ZA","resumen":"Metro contador electrónico de energía, carril DIM, digital, monofásico.\n\r\n(Corriente nominal a elegir dentro del producto)","descripcion":" Available as 35mm DIN standard rail mounted, conforming to Standards DIN EN 50022, as well as front PANEL mounted (the center distance between two mounting holes is 63mm or 67mm). Two mounted methods above are optional for user.\n 6 pole width (modulus 12.5mm), complying with Standards JB/T7121-1993.\n Can select the step motor impulse register of 5+1 digits (99999.1kWh) or 6+1 digits (999999.1kWh) LCD display.\n Can select two LCD displays with 6 digits, to show total power (5+1 digits display), and realtime power (4+2 digits display) which can be cleared by the red button on the nameplate. This red button can be protected by the seal and this model meter suits for the renting house.\n Can select the inside load switch for the remote control credit.\n Can select the inside far infrared data communication port and RS485 data communication port, the communication protocol complies with Standards DL/T645-1997, can also select the other communication protocol.\n Equipped with a polarity passive energy impulse output terminal, conforming to Standards IEC 62053-31 and DIN 43864.\n Two LEDs to indicate separately the power state (green) and the energy impulse signal (red).\n Measure the active energy consumption in one direction on single phase two wire, which is not related with the load current flow direction at all, complying with Standards IEC 62053-21.\n Direct connection for use. Two connections: type S and type T for option.\n The short terminal cover is made with the transparent PC, to reduce the installation space and is convenient for centralized installation.","caracteristicas":[{"name":"Corriente de arranque: ","value":" \t0.02 / 0.04 / 0.08 A (dependiendo de la corriente nominal seleccionada) "},{"name":"Corriente Nominal: ","value":"5(30) / 10(60) / 20(120) Seleccione "},{"name":"Metro Contador","value":"digital de 2 lineas de 6 dígitos LCD para la medida en tiempo real "},{"name":"Prestaciones de aislamiento: ","value":"4 kV tensión de CA durante 1 minuto, de forma de onda de tensión de 6 kV 1.2/50us impulso. "},{"name":"Voltaje de Referencia: ","value":"230 V"}],"opciones":[{"name":"Corriente Nominal","value":"10 (60)A, con corriente de arranque 0.04 A"},{"name":"Corriente Nominal","value":"20 (120)A, con corriente de arranque 0.08"},{"name":"Corriente Nominal","value":"5 (30)A, con corriente de arranque 0.02"}],"imagenes":["../tienda/img/p/4/4/44.jpg"],"ficha":"index.php?producto=10"},{"id":11,"nombre":"ECO021AG","referencia":"ECO021AG","resumen":"Metro contador electrónico de energía, carril DIM, analógico, trifásico.\n\r\n(Corriente nominal a elegir dentro del producto)","descripcion":" 3 Available as 35mm DIN standard rail mounted, conforming to Standards DIN EN 50022, as well as front PANEL mounted (the center distance between two mounting holes is 63mm). Two mounted methods above are optional for user.\n 10 pole width (modulus 12.5mm), complying with Standards JB/T7121-1993.\n Can select the step motor impulse register of 6 digits (999999kWh) or 6+1 digits (999999.1kWh) LCD display.\n Can select the inside far infrared data communication port and RS485 data communication port. The communication protocol complies with Standards DL/T645-1997. The other communication protocol can also be option.\n Can select the maintenance free lithium battery inside for LCD display to read the meter while the power is cut.\n S-connection (inlet wire from bottom and outlet wire on top) has two connection types: direct connection and CT connection for option. For CT connection, there are 27 kinds CT rates to set, after setting CT, we can read the meter directly, no need multiplying the CT rates.\n The CT connection meter is 7 digits LCD display: 5+2 digits (only at CT rate is 5:5A) or 7 integers, which is depended on the setting CT rate.\n Equipped with a polarity passive energy impulse output terminal, conforming to Standards IEC 62053-31 and DIN 43864.\n LEDs indicate separately the power state on each phase, the energy impulse signal and data communication state.\n Automatic detection for the load current flow direction and will be indicated by LED.\n Measure the active energy consumption in one direction on three phase, which is not related with the load current flow direction at all, complying with Standards IEC 62053-21.\n The short terminal cover is made with the transparent PC, to reduce the installation space and is convenient for centralized installation.","caracteristicas":[{"name":"Corriente de arranque: ","value":" \t0.02 / 0.04 / 0.08 A (dependiendo de la corriente nominal seleccionada) "},{"name":"Corriente Nominal: ","value":"5(30) / 10(60) / 20(120) Seleccione "},{"name":"Metro Contador","value":"analógico de 6 dígito"},{"name":"Prestaciones de aislamiento: ","value":"4 kV tensión de CA durante 1 minuto, de forma de onda de tensión de 6 kV 1.2/50us impulso. "},{"name":"Voltaje de Referencia: ","value":"230 V"}],"opciones":[{"name":"Corriente Nominal","value":"10 (60)A, con corriente de arranque 0.04 A"},{"name":"Corriente Nominal","value":"20 (120)A, con corriente de arranque 0.08"},{"name":"Corriente Nominal","value":"5 (30)A, con corriente de arranque 0.02"}],"imagenes":["../tienda/img/p/3/3/33.jpg"],"ficha":"index.php?producto=11"},{"id":13,"nombre":"ECO021GC","referencia":"ECO021GC","resumen":"Metro contador electrónico de energía, carril DIM, digital, trifásico.\n\r\n(Corriente nominal a elegir dentro del producto)","descripcion":" 3 Available as 35mm DIN standard rail mounted, conforming to Standards DIN EN 50022, as well as front PANEL mounted (the center distance between two mounting holes is 63mm). Two mounted methods above are optional for user.\n 10 pole width (modulus 12.5mm), complying with Standards JB/T7121-1993.\n Can select the step motor impulse register of 6 digits (999999kWh) or 6+1 digits (999999.1kWh) LCD display.\n Can select the inside far infrared data communication port and RS485 data communication port. The communication protocol complies with Standards DL/T645-1997. The other communication protocol can also be option.\n Can select the maintenance free lithium battery inside for LCD display to read the meter while the power is cut.\n S-connection (inlet wire from bottom and outlet wire on top) has two connection types: direct connection and CT connection for option. For CT connection, there are 27 kinds CT rates to set, after setting CT, we can read the meter directly, no need multiplying the CT rates.\n The CT connection meter is 7 digits LCD display: 5+2 digits (only at CT rate is 5:5A) or 7 integers, which is depended on the setting CT rate.\n Equipped with a polarity passive energy impulse output terminal, conforming to Standards IEC 62053-31 and DIN 43864.\n LEDs indicate separately the power state on each phase, the energy impulse signal and data communication state.\n Automatic detection for the load current flow direction and will be indicated by LED.\n Measure the active energy consumption in one direction on three phase, which is not related with the load current flow direction at all, complying with Standards IEC 62053-21.\n The short terminal cover is made with the transparent PC, to reduce the installation space and is convenient for centralized installation.\n\r\n\n\r\n ","caracteristicas":[{"name":"Corriente de arranque: ","value":" \t0.02 / 0.04 / 0.08 A (dependiendo de la corriente nominal seleccionada) "},{"name":"Corriente Nominal: ","value":"5(30) / 10(60) / 20(120) Seleccione "},{"name":"Metro Contador","value":"digital de 6 + 1 dígitos LCD"},{"name":"Prestaciones de aislamiento: ","value":"4 kV tensión de CA durante 1 minuto, de forma de onda de tensión de 6 kV 1.2/50us impulso. "},{"name":"Voltaje de Referencia: ","value":"230 V"}],"opciones":[{"name":"Corriente Nominal","value":"10 (60)A, con corriente de arranque 0.04 A"},{"name":"Corriente Nominal","value":"20 (120)A, con corriente de arranque 0.08"},{"name":"Corriente Nominal","value":"5 (30)A, con corriente de arranque 0.02"}],"imagenes":["../tienda/img/p/3/6/36.jpg"],"ficha":"index.php?producto=13"},{"id":14,"nombre":"ECO031AL","referencia":"ECO031AL","resumen":"Metro contador electrónico de energía, carril DIM, multirate, digital, monofásico.\n\r\n(Corriente nominal a elegir dentro del producto)","descripcion":" Available as 35mm DIN standard rail mounted, conforming to Standards DIN EN 50022, as well as front PANEL mounted (the center distance between two mounting holes is 63mm). Two mounted methods above are optional for user.\n 6 pole width (modulus 12.5mm), complying with Standards JB/T7121-1993.\n Can select time-of-use metering in 3 tariffs. Can set 12 daily intervals. Can freely set the date in every month to read meter automatically. Can set single tariff at weekends.\n Can select 2 tariffs metering, equipped with the tariff setting port, if the input control voltage is 0 - 90 Vac, the setting tariff is F1. If the input control voltage is 150 - 400 Vac, the setting tariff is F2. Tariff transduction is controlled by the external timer or similar device.\n The meter with time-of-use metering in 3 tariffs has clock chip inside and maintenance free lithium battery inside. The battery capacity can be detected in real time and displayed,\nkeeping the data for 12 months.\n 7 digits LCD with two options: cycle display (default) or push-bottom display item by item. Can set the cycle display interval. Can select the data item of display. The decimal of the data display can be set to be 1 or 2 digits.\n Can select the inside far infrared data communication port and RS485 data communication port for meter setting or reading meter. The meter setting has password protection. The communication protocol complies with Standards DL/T645-1997, can also select the other\ncommunication protocol.\n S-connection (inlet wire from bottom and outlet wire on top) and direct connection.\n Equipped with a polarity passive energy impulse output terminal, conforming to Standards IEC 62053-31 and DIN 43864.\n LEDs indicate separately the power state, the energy impulse signal, load current flow direction, current tariff state and data communication state.\n Measure the active energy consumption in one direction on single phase two wire, which is not related with the load current flow direction at all, complying with Standards IEC 62053-21.\n The short terminal cover is made with the transparent PC, to reduce the installation space and is convenient for centralized installation.","caracteristicas":[{"name":"Corriente de arranque: ","value":" \t0.02 / 0.04 / 0.08 A (dependiendo de la corriente nominal seleccionada) "},{"name":"Corriente Nominal: ","value":"5(30) / 10(60) / 20(120) Seleccione "},{"name":"Metro Contador","value":"de tres tarifas y reloj chip interno"},{"name":"Prestaciones de aislamiento: ","value":"4 kV tensión de CA durante 1 minuto, de forma de onda de tensión de 6 kV 1.2/50us impulso. "},{"name":"Voltaje de Referencia: ","value":"230 V"}],"opciones":[{"name":"Corriente Nominal","value":"10 (60)A, con corriente de arranque 0.04 A"},{"name":"Corriente Nominal","value":"20 (120)A, con corriente de arranque 0.08"},{"name":"Corriente Nominal","value":"5 (30)A, con corriente de arranque 0.02"}],"imagenes":["../tienda/img/p/4/5/45.jpg"],"ficha":"index.php?producto=14"},{"id":15,"nombre":"ECO041AL","referencia":"ECO041AL","resumen":"Metro contador electrónico de energía, carril DIM, multirate, digital, trifásico.\n\r\n(Corriente nominal a elegir dentro del producto)","descripcion":" Available as 35mm DIN standard rail mounted, conforming to Standards DIN EN 50022, as well as front PANEL mounted (the center distance between two mounting holes is 63mm). Two mounted methods above are optional for user.\n 10 pole width (modulus 12.5mm), complying with Standards JB/T7121-1993.\n Can select time-of-use metering in 3 tariffs. Can set 12 daily intervals. Can freely set the date in every month to read meter automatically. Can set single tariff at weekends.\n Can select 2 tariffs metering, equipped with the tariff setting port, if the input control voltage is 0 - 90 Vac, the setting tariff is F1. If the input control voltage is 150 - 400 Vac, the setting tariff is F2. Tariff transduction is controlled by the external timer or similar device.\n The meter with time-of-use metering in 3 tariffs has clock chip inside and maintenance free lithium battery inside. The battery capacity can be detected in real time and displayed, keeping the data for 12 months.\n 7 digits LCD with two options: cycle display (default) or push-bottom display item by item. Can set the cycle display interval. Can select the data item of display. The decimal of the data display can be set to be 1 or 2 digits.\n Can select the inside far infrared data communication port and RS485 data communication port for meter setting or reading meter. The meter setting has password protection. The communication protocol complies with Standards DL/T645-1997, can also select the other\ncommunication protocol.\n S-connection (inlet wire from bottom and outlet wire on top) has two connection types: direct connection and CT connection for option.\n For CT connection meter, it is indirect reading or direct reading for option. For direct reading, there are 27 kinds CT rates to set, after setting CT rate, we can read the meter directly, no need multiplying the CT rate.\n The CT direct reading meter is 7 digits LCD display: 5+2 digits (only at CT rate is 5:5A) or 7 integers, which is depended on the setting CT rate.\n With a non-volatile memory, keep the data for permanently while the power is cut.\n Equipped with a polarity passive energy impulse output terminal, conforming to Standards IEC 62053-31 and DIN 43864.\n LEDs indicate separately the power state on each phase, the energy impulse signal, load current flow direction, current tariff state and data communication state.\n Automatic detection for the load current flow direction and will be indicated by LED.\n Measure the active energy consumption in one direction on three phases, which is not related with the load current flow direction at all, complying with Standards IEC 62053-21.\n The short terminal cover is made with the transparent PC, to reduce the installation space and is convenient for centralized installation.","caracteristicas":[{"name":"Corriente de arranque: ","value":" \t0.02 / 0.04 / 0.08 A (dependiendo de la corriente nominal seleccionada) "},{"name":"Corriente Nominal: ","value":"5(30) / 10(60) / 20(120) Seleccione "},{"name":"Metro Contador","value":"de tres tarifas y reloj chip interno"},{"name":"Prestaciones de aislamiento: ","value":"4 kV tensión de CA durante 1 minuto, de forma de onda de tensión de 6 kV 1.2/50us impulso. "},{"name":"Voltaje de Referencia: ","value":"230 V"}],"opciones":[{"name":"Corriente Nominal","value":"10 (60)A, con corriente de arranque 0.04 A"},{"name":"Corriente Nominal","value":"20 (120)A, con corriente de arranque 0.08"},{"name":"Corriente Nominal","value":"5 (30)A, con corriente de arranque 0.02"}],"imagenes":["../tienda/img/p/4/7/47.jpg"],"ficha":"index.php?producto=15"},{"id":16,"nombre":"ECO052AH","referencia":"ECO052AH","resumen":"Metro contador electrónico de energía, montaje sobre panel frontal, analógico, monofásico.\n\r\n(Corriente nominal a elegir dentro del producto)","descripcion":" Front panel mounted in 3 points for fixing. The centre-to-centre distance between the top mounting holes and the bottom one is 130 -147 mm, which the user can select any needed distance, in accordance with Standards BS 7856 and DIN 43857.\n Can select the step motor impulse register of 5+1 digits (99999.1kWh) or 6+1 digits (999999.1kWh) LCD display.\n Can select the maintenance free lithium battery inside for LCD display to read the meter while the power is cut.\n Equipped with a polarity passive energy impulse output terminal, conforming to Standards IEC 62053-31 and DIN 43864.\n LEDs indicate the power state (green) and the energy impulse signal (red).\n Automatic detection for the load current flow direction and will be indicated by LED.\n Measure the active energy consumption in one direction on single phase two wire or single phase three wire, which is not related with the load current flow direction at all, complying with Standards IEC 62053-21.\n Direct connection. For single phase two wire, two types of connections: type 1A and type 1B for option. For single phase three wire, the connection is type 2A.\n Can select the extended terminal cover or short terminal cover.","caracteristicas":[{"name":"Corriente de arranque: ","value":" \t0.02 / 0.04 / 0.08 A (dependiendo de la corriente nominal seleccionada) "},{"name":"Corriente Nominal: ","value":"5(30) / 10(60) / 20(120) Seleccione "},{"name":"Metro Contador","value":"analógico de 5 + 1 dígitos"},{"name":"Prestaciones de aislamiento: ","value":"4 kV tensión de CA durante 1 minuto, de forma de onda de tensión de 6 kV 1.2/50us impulso. "},{"name":"Voltaje de Referencia: ","value":"230 V"}],"opciones":[{"name":"Corriente Nominal","value":"10 (60)A, con corriente de arranque 0.04 A"},{"name":"Corriente Nominal","value":"20 (120)A, con corriente de arranque 0.08"},{"name":"Corriente Nominal","value":"5 (30)A, con corriente de arranque 0.02"}],"imagenes":["../tienda/img/p/5/0/50.jpg"],"ficha":"index.php?producto=16"},{"id":17,"nombre":"ECO052JF","referencia":"ECO052JF","resumen":"Metro contador electrónico de energía, montaje sobre panel frontal, digital, monofásico.\n\r\n(Corriente nominal a elegir dentro del producto)","descripcion":" Front panel mounted in 3 points for fixing. The centre-to-centre distance between the top mounting holes and the bottom one is 130 -147 mm, which the user can select any needed distance, in accordance with Standards BS 7856 and DIN 43857.\n Can select the step motor impulse register of 5+1 digits (99999.1kWh) or 6+1 digits (999999.1kWh) LCD display.\n Can select the maintenance free lithium battery inside for LCD display to read the meter while the power is cut.\n Equipped with a polarity passive energy impulse output terminal, conforming to Standards IEC 62053-31 and DIN 43864.\n LEDs indicate the power state (green) and the energy impulse signal (red).\n Automatic detection for the load current flow direction and will be indicated by LED.\n Measure the active energy consumption in one direction on single phase two wire or single phase three wire, which is not related with the load current flow direction at all, complying with Standards IEC 62053-21.\n Direct connection. For single phase two wire, two types of connections: type 1A and type 1B for option. For single phase three wire, the connection is type 2A.\n Can select the extended terminal cover or short terminal cover.","caracteristicas":[{"name":"Corriente de arranque: ","value":" \t0.02 / 0.04 / 0.08 A (dependiendo de la corriente nominal seleccionada) "},{"name":"Corriente Nominal: ","value":"5(30) / 10(60) / 20(120) Seleccione "},{"name":"Metro Contador","value":"analógico de 5 + 1 dígitos"},{"name":"Prestaciones de aislamiento: ","value":"4 kV tensión de CA durante 1 minuto, de forma de onda de tensión de 6 kV 1.2/50us impulso. "},{"name":"Voltaje de Referencia: ","value":"230 V"}],"opciones":[{"name":"Corriente Nominal","value":"10 (60)A, con corriente de arranque 0.04 A"},{"name":"Corriente Nominal","value":"20 (120)A, con corriente de arranque 0.08"},{"name":"Corriente Nominal","value":"5 (30)A, con corriente de arranque 0.02"}],"imagenes":["../tienda/img/p/5/2/52.jpg"],"ficha":"index.php?producto=17"},{"id":18,"nombre":"ECO053AH","referencia":"ECO053AH","resumen":"Metro contador electrónico de energía, montaje sobre panel frontal, analógico, monofásico.\n\r\n(Corriente nominal a elegir dentro del producto)","descripcion":" Front panel mounted in 3 points for fixing. The centre-to-centre distance between the top\nmounting holes and the bottom one is 126 - 141 mm, which the user can select any needed\ndistance, in accordance with Standards BS 7856 and DIN 43857.\n Can select the step motor impulse register of 5+1 digits (99999.1kWh) or 6+1 digits\n(999999.1kWh) LCD display.\n Can select the maintenance free lithium battery inside for LCD display to read the meter while the\npower is cut.\n Equipped with a polarity passive energy impulse output terminal, conforming to Standards\nIEC 62053-31 and DIN 43864.\n LEDs indicate the power state (green) and the energy impulse signal (red).\n Automatic detection for the load current flow direction and will be indicated by LED.\n Measure the active energy consumption in one direction on single phase two wire or single\nphase three wire, which is not related with the load current flow direction at all, complying with\nStandards IEC 62053-21.\n Direct connection. For single phase two wire, two types of connections: type 1A and type 1B\nfor option. For single phase three wire, the connection is type 2A.\n Can select the extended terminal cover or short terminal cover.","caracteristicas":[{"name":"Corriente de arranque: ","value":" \t0.02 / 0.04 / 0.08 A (dependiendo de la corriente nominal seleccionada) "},{"name":"Corriente Nominal: ","value":"5(30) / 10(60) / 20(120) Seleccione "},{"name":"Metro Contador","value":"analógico de 5 + 1 dígitos"},{"name":"Prestaciones de aislamiento: ","value":"4 kV tensión de CA durante 1 minuto, de forma de onda de tensión de 6 kV 1.2/50us impulso. "},{"name":"Voltaje de Referencia: ","value":"230 V"}],"opciones":[{"name":"Corriente Nominal","value":"10 (60)A, con corriente de arranque 0.04 A"},{"name":"Corriente Nominal","value":"20 (120)A, con corriente de arranque 0.08"},{"name":"Corriente Nominal","value":"5 (30)A, con corriente de arranque 0.02"}],"imagenes":["../tienda/img/p/5/3/53.jpg"],"ficha":"index.php?producto=18"},{"id":19,"nombre":"ECO053JF","referencia":"ECO053JF","resumen":"Metro contador electrónico de energía, montaje sobre panel frontal, digital, monofásico.\n\r\n(Corriente nominal a elegir dentro del producto)","descripcion":" Front panel mounted in 3 points for fixing. The centre-to-centre distance between the top\nmounting holes and the bottom one is 126 - 141 mm, which the user can select any needed\ndistance, in accordance with Standards BS 7856 and DIN 43857.\n Can select the step motor impulse register of 5+1 digits (99999.1kWh) or 6+1 digits\n(999999.1kWh) LCD display.\n Can select the maintenance free lithium battery inside for LCD display to read the meter while the\npower is cut.\n Equipped with a polarity passive energy impulse output terminal, conforming to Standards\nIEC 62053-31 and DIN 43864.\n LEDs indicate the power state (green) and the energy impulse signal (red).\n Automatic detection for the load current flow direction and will be indicated by LED.\n Measure the active energy consumption in one direction on single phase two wire or single\nphase three wire, which is not related with the load current flow direction at all, complying with\nStandards IEC 62053-21.\n Direct connection. For single phase two wire, two types of connections: type 1A and type 1B\nfor option. For single phase three wire, the connection is type 2A.\n Can select the extended terminal cover or short terminal cover.","caracteristicas":[{"name":"Corriente de arranque: ","value":" \t0.02 / 0.04 / 0.08 A (dependiendo de la corriente nominal seleccionada) "},{"name":"Corriente Nominal: ","value":"5(30) / 10(60) / 20(120) Seleccione "},{"name":"Metro Contador","value":"digital de 6 + 1 dígitos LCD"},{"name":"Prestaciones de aislamiento: ","value":"4 kV tensión de CA durante 1 minuto, de forma de onda de tensión de 6 kV 1.2/50us impulso. "},{"name":"Voltaje de Referencia: ","value":"230 V"}],"opciones":[{"name":"Corriente Nominal","value":"10 (60)A, con corriente de arranque 0.04 A"},{"name":"Corriente Nominal","value":"20 (120)A, con corriente de arranque 0.08"},{"name":"Corriente Nominal","value":"5 (30)A, con corriente de arranque 0.02"}],"imagenes":["../tienda/img/p/5/6/56.jpg"],"ficha":"index.php?producto=19"},{"id":20,"nombre":"ECO061AG","referencia":"ECO061AG","resumen":"Metro contador electrónico de energía, montaje sobre panel frontal, analógico, trifásico.\n\r\n(Corriente nominal a elegir dentro del producto)","descripcion":" Front panel mounted in 3 points for fixing. The centre-to-centre distance between the top mounting holes and the bottom one is 198-212 mm, which the user can select any needed distance, in accordance with Standards BS 7856 and DIN 43857.\n Can select the step motor impulse register of 6 digits (999999kWh) or 6+1 digits (999999.1kWh) LCD display.\n Can select the maintenance free lithium battery inside for LCD display to read the meter while the power is cut.\n Direct connection and CT connection for option.\n For CT connection meter, it is indirect reading or direct reading for option. For direct reading, there are 27 kinds CT rates to set, after setting CT, we can read the meter directly, no need multiplying the CT rates.\n The CT direct reading meter is 7 digits LCD display: 5+2 digits (only at CT rate is 5:5A) or 7 integers, which is depended on the setting CT rate.\n Equipped with a polarity passive energy impulse output terminal, conforming to Standards IEC 62053-31 and DIN 43864.\n LEDs indicate separately the power state on each phase and the energy impulse signal.\n Automatic detection for the load current flow direction and will be indicated by LED.\n Measure the active energy consumption in one direction on three phase, which is not related with the load current flow direction at all, complying with Standards IEC 62053-21.\n Can select the extended terminal cover or short terminal cover.","caracteristicas":[{"name":"Corriente de arranque: ","value":" \t0.02 / 0.04 / 0.08 A (dependiendo de la corriente nominal seleccionada) "},{"name":"Corriente Nominal: ","value":"5(30) / 10(60) / 20(120) Seleccione "},{"name":"Metro Contador","value":"analógico de 6 dígito"},{"name":"Prestaciones de aislamiento: ","value":"4 kV tensión de CA durante 1 minuto, de forma de onda de tensión de 6 kV 1.2/50us impulso. "},{"name":"Voltaje de Referencia: ","value":"230 V"}],"opciones":[{"name":"Corriente Nominal","value":"10 (60)A, con corriente de arranque 0.04 A"},{"name":"Corriente Nominal","value":"20 (120)A, con corriente de arranque 0.08"},{"name":"Corriente Nominal","value":"5 (30)A, con corriente de arranque 0.02"}],"imagenes":["../tienda/img/p/5/7/57.jpg"],"ficha":"index.php?producto=20"},{"id":21,"nombre":"ECO061JK","referencia":"ECO061JK","resumen":"Metro contador electrónico de energía, montaje sobre panel frontal, analógico, trifásico.\n\r\n(Corriente nominal a elegir dentro del producto)","descripcion":" Front panel mounted in 3 points for fixing. The centre-to-centre distance between the top mounting holes and the bottom one is 198-212 mm, which the user can select any needed distance, in accordance with Standards BS 7856 and DIN 43857.\n Can select the step motor impulse register of 6 digits (999999kWh) or 6+1 digits (999999.1kWh) LCD display.\n Can select the maintenance free lithium battery inside for LCD display to read the meter while the power is cut.\n Direct connection and CT connection for option.\n For CT connection meter, it is indirect reading or direct reading for option. For direct reading, there are 27 kinds CT rates to set, after setting CT, we can read the meter directly, no need multiplying the CT rates.\n The CT direct reading meter is 7 digits LCD display: 5+2 digits (only at CT rate is 5:5A) or 7 integers, which is depended on the setting CT rate.\n Equipped with a polarity passive energy impulse output terminal, conforming to Standards IEC 62053-31 and DIN 43864.\n LEDs indicate separately the power state on each phase and the energy impulse signal.\n Automatic detection for the load current flow direction and will be indicated by LED.\n Measure the active energy consumption in one direction on three phase, which is not related with the load current flow direction at all, complying with Standards IEC 62053-21.\n Can select the extended terminal cover or short terminal cover.\n\n\n\r\n\n\r\n ","caracteristicas":[{"name":"Corriente de arranque: ","value":" \t0.02 / 0.04 / 0.08 A (dependiendo de la corriente nominal seleccionada) "},{"name":"Corriente Nominal: ","value":"5(30) / 10(60) / 20(120) Seleccione "},{"name":"Metro Contador","value":"digital de 6 + 1 dígitos LCD"},{"name":"Prestaciones de aislamiento: ","value":"4 kV tensión de CA durante 1 minuto, de forma de onda de tensión de 6 kV 1.2/50us impulso. "},{"name":"Voltaje de Referencia: ","value":"230 V"}],"opciones":[{"name":"Corriente Nominal","value":"10 (60)A, con corriente de arranque 0.04 A"},{"name":"Corriente Nominal","value":"20 (120)A, con corriente de arranque 0.08"},{"name":"Corriente Nominal","value":"5 (30)A, con corriente de arranque 0.02"}],"imagenes":["../tienda/img/p/5/8/58.jpg"],"ficha":"index.php?producto=21"},{"id":22,"nombre":"ECO091PA","referencia":"ECO091PA","resumen":"Metro contador electrónico prepago de energía, montaje sobre panel frontal, digital, monofásico, pantalla led.\n\r\n(Corriente nominal a elegir dentro del producto)","descripcion":" Front panel mounted in 3 points for fixing, the appearance and dimensions are in accordance with Standards BS 7856 and DIN 43857.\n 6 digits LED or 7 digits LCD display for option.\n Can select one meter with one card and the card can be reloadable via the computer with an IC card programmer.\n Can select the meter suitable for both reloadable IC card and disposable IC card. To load, please let both IC card programmer and the computer on line. It is also available to load via the separate offline IC card programmer.\n Can select the inside far infrared communication module and RS485 communication module, for reading meter, remote control credit and system parameter setting.\n Keypad IC card programmer and universal IC card programmer for option.\n IC card is with data encryption and anti-fake protection.\n Prepayment mode is by kWh. Another mode by credit is for option when ordering.\n Standard configuration of prepayment management system software is a single computer version. Network version is for option when ordering.\n Have the functions of load control, automatic detection and indication of fault. Standard configuration is without the detection function of opening terminal cover. When ordering, you can add the function: while opening terminal cover, the power will be cut.\n Equipped with a polarity passive energy impulse output terminal, conforming to Standards IEC 62053-31 and DIN 43864.\n LEDs indicate separately the power state (green), the energy impulse signal (red), load current flow direction (yellow).\n Automatic detection for the load current flow direction, yellow LED lighting means reverse current flow.\n Measure the active energy consumption in one direction on single phase two wire, which is ot related with the load current flow direction at all, complying with Standards IEC 62053- 21.\n Direct connection. Two types of connections: type 1A and type 1B for option.\n Can select the extended terminal cover or short terminal cover.","caracteristicas":[{"name":"Corriente de arranque: ","value":" \t0.02 / 0.04 / 0.08 A (dependiendo de la corriente nominal seleccionada) "},{"name":"Corriente Nominal: ","value":"5(30) / 10(60) / 20(120) Seleccione "},{"name":"Metro Contador","value":"con 6 dígitos led"},{"name":"Prestaciones de aislamiento: ","value":"4 kV tensión de CA durante 1 minuto, de forma de onda de tensión de 6 kV 1.2/50us impulso. "},{"name":"Voltaje de Referencia: ","value":"230 V"}],"opciones":[{"name":"Corriente Nominal","value":"10 (60)A, con corriente de arranque 0.04 A"},{"name":"Corriente Nominal","value":"20 (120)A, con corriente de arranque 0.08"},{"name":"Corriente Nominal","value":"5 (30)A, con corriente de arranque 0.02"}],"imagenes":["../tienda/img/p/5/9/59.jpg"],"ficha":"index.php?producto=22"},{"id":23,"nombre":"ECO091QA","referencia":"ECO091QA","resumen":"Metro contador electrónico prepago de energía, montaje sobre panel frontal, digital, monofásico, pantalla LCD.\n\r\n(Corriente nominal a elegir dentro del producto)","descripcion":" Front panel mounted in 3 points for fixing, the appearance and dimensions are in accordance with Standards BS 7856 and DIN 43857.\n 6 digits LED or 7 digits LCD display for option.\n Can select one meter with one card and the card can be reloadable via the computer with an IC card programmer.\n Can select the meter suitable for both reloadable IC card and disposable IC card. To load, please let both IC card programmer and the computer on line. It is also available to load via the separate offline IC card programmer.\n Can select the inside far infrared communication module and RS485 communication module, for reading meter, remote control credit and system parameter setting.\n Keypad IC card programmer and universal IC card programmer for option.\n IC card is with data encryption and anti-fake protection.\n Prepayment mode is by kWh. Another mode by credit is for option when ordering.\n Standard configuration of prepayment management system software is a single computer version. Network version is for option when ordering.\n Have the functions of load control, automatic detection and indication of fault. Standard configuration is without the detection function of opening terminal cover. When ordering, you can add the function: while opening terminal cover, the power will be cut.\n Equipped with a polarity passive energy impulse output terminal, conforming to Standards IEC 62053-31 and DIN 43864.\n LEDs indicate separately the power state (green), the energy impulse signal (red), load current flow direction (yellow).\n Automatic detection for the load current flow direction, yellow LED lighting means reverse current flow.\n Measure the active energy consumption in one direction on single phase two wire, which is ot related with the load current flow direction at all, complying with Standards IEC 62053- 21.\n Direct connection. Two types of connections: type 1A and type 1B for option.\n Can select the extended terminal cover or short terminal cover.\n\r\n\n\r\n ","caracteristicas":[{"name":"Corriente de arranque: ","value":" \t0.02 / 0.04 / 0.08 A (dependiendo de la corriente nominal seleccionada) "},{"name":"Corriente Nominal: ","value":"5(30) / 10(60) / 20(120) Seleccione "},{"name":"Metro Contador","value":"digital de 7 dígitos LCD"},{"name":"Prestaciones de aislamiento: ","value":"4 kV tensión de CA durante 1 minuto, de forma de onda de tensión de 6 kV 1.2/50us impulso. "},{"name":"Voltaje de Referencia: ","value":"230 V"}],"opciones":[{"name":"Corriente Nominal","value":"10 (60)A, con corriente de arranque 0.04 A"},{"name":"Corriente Nominal","value":"20 (120)A, con corriente de arranque 0.08"},{"name":"Corriente Nominal","value":"5 (30)A, con corriente de arranque 0.02"}],"imagenes":["../tienda/img/p/6/0/60.jpg"],"ficha":"index.php?producto=23"},{"id":24,"nombre":"ECO101PA","referencia":"ECO101PA","resumen":"Metro contador electrónico prepago de energía, montaje sobre panel frontal, digital, trifásico.\n\r\n(Corriente nominal a elegir dentro del producto)","descripcion":" Front panel mounted in 3 points for fixing, the appearance and dimensions are in accordance with Standards BS 7856 and DIN 43857.\n 6 digits LED or 7 digits LCD display for option.\n Can select one meter with one card and the card can be reloadable via the computer with an IC card programmer.\n Can select the meter suitable for both reloadable IC card and disposable IC card. To load, please let both IC card programmer and the computer on line. It is also available to load via the separate offline IC card programmer.\n Keypad IC card programmer and universal IC card programmer for option.\n IC card is with data encryption and anti-fake protection.\n Prepayment mode is by kWh. Another mode by credit is for option when ordering.\n Standard configuration of prepayment management system software is a single computer version. Network version is for option when ordering.\n Have the functions of load control, automatic detection and indication of fault. Standard configuration is without the detection function of opening terminal cover. When ordering, you can add the function: while opening terminal cover, the power will be cut.\n Equipped with a polarity passive energy impulse output terminal, conforming to Standards IEC 62053-31 and DIN 43864.\n LEDs indicate separately the power state on each phase, the energy impulse signal and load current flow direction.\n Automatic detection for the load current flow direction. LED lighting of load current flow direction means reverse current flow.\n Three elements measure the active energy consumption in one direction on three phase four wire, which is not related with the load current flow directio nat all, complying with Standards IEC 62053-21.\n Direct connection and CT connection for option. The type of direct connection is type 16B. The type of CT connection is type 48B.\n Can select the extended terminal cover or short terminal cover.","caracteristicas":[{"name":"Corriente de arranque: ","value":" \t0.02 / 0.04 / 0.08 A (dependiendo de la corriente nominal seleccionada) "},{"name":"Corriente Nominal: ","value":"5(30) / 10(60) / 20(120) Seleccione "},{"name":"Metro Contador","value":"con 6 dígitos led"},{"name":"Prestaciones de aislamiento: ","value":"4 kV tensión de CA durante 1 minuto, de forma de onda de tensión de 6 kV 1.2/50us impulso. "},{"name":"Voltaje de Referencia: ","value":"230 V"}],"opciones":[{"name":"Corriente Nominal","value":"10 (60)A, con corriente de arranque 0.04 A"},{"name":"Corriente Nominal","value":"20 (120)A, con corriente de arranque 0.08"},{"name":"Corriente Nominal","value":"5 (30)A, con corriente de arranque 0.02"}],"imagenes":["../tienda/img/p/6/1/61.jpg"],"ficha":"index.php?producto=24"},{"id":33,"nombre":"Pack  Básico secillo","referencia":"","resumen":"El pack básico sensillo Incluye:\n\r\n\r\n1 Contador Prepago (ECO091PA de corriente nominal 10 (60)A\n\r\n4 Tarjetas chip preprogramadas con 20kw, 50kw, 100kw y una tarjeta reset.\n\r\n\r\n \n\r\nCon este pack, usted no necesita del lector grabador, ya que le proporcionamos las tajetas previamente programadas con las que usted puede operar en tiempo indefinido.","descripcion":"El sistema es sencillo y de rápida implementación:  \n\n\r\nSe instala un Contador Prepago (entiéndase contador de luz prepago), en la entrada del tablero eléctrico del apartamento que se desee controlar. \n\n El contador prepago “Lee” la información que se le suministra mediante una Tarjeta Chip preprogramada e indica en todo momento la electricidad que se ha consumido y la disponible, en ese apartamento en particular, además tiene programada una señal de alarma que avisa con mucha antelación de que están agotando los kw cargados.\n\n\r\nUsted tendrá la opción de cargarle al contador 20kw, 50kw ó 100kw, en función de la estancia que vaya a relizar el turista\r\n\n\r\nAl finalizar la estancia, usted puede leer en el contador los kw que han sido consumidos y cobrarle al turista  lo que haya pactado en Euros/kw\r\n\nAhora el gasto de electricidad puede ser controlado por el inquilino, el cual se esforzará por reducirlo porque le afecta directamente, le damos la información para que sea responsable y siga comprometido como si estuviera en su domicilio habitual, solo pagará lo que consuma. \n\n Esta instalación no interfiere con la compañía de suministro eléctrico, es totalmente legal y no infringe ninguna normativa vigente de Baja Tensión.","caracteristicas":[],"opciones":[],"imagenes":["../tienda/img/p/8/7/87.jpg"],"ficha":"index.php?producto=33"},{"id":34,"nombre":"pack 4 tarjetas programadas","referencia":"","resumen":"Tarjeta chip para la recarga de los contadores prepago. Incluye 4 tarjetas programadas con 50kw, 100kw y 500kw.","descripcion":"La programación puede venir dada en función de la necesidad de cada cliente.","caracteristicas":[],"opciones":[],"imagenes":["../tienda/img/p/8/8/88.jpg"],"ficha":"index.php?producto=34"},{"id":27,"nombre":"Pack Kit Básico 1-apartamento","referencia":"","resumen":"El pack Incluye:\n\r\n\r\n1 Contador Prepago (ECO091PA de corriente nominal 10 (60)A\n\r\n1 Lector / Grabador con software (Programador de tarjetas chip con software de control)\n\r\n2 Tarjetas chip","descripcion":"El sistema es sencillo y de rápida implementación:  \n\n\r\nSe instala un Contador Prepago (entiéndase contador de luz prepago), en la entrada del tablero eléctrico del apartamento que se desee controlar. \n\n El contador prepago “Lee” la información que se le suministra mediante una Tarjeta Chip e indica en todo momento la electricidad que se ha consumido y la disponible, en ese apartamento en particular, además permite programar una señal de alarma que avisa con mucha antelación que se debe recargar para no perder el suministro. \n\nSi llegado el caso, el consumo “cargado” se agota, el contador de luz prepago corta el servicio eléctrico. \n\nPara que esto no suceda, se debe “recargar” la tarjeta Chip con más saldo (pre-pagando a la administración) y con esto se recarga el contador de luz prepago, las veces que haga falta. \n\nComo el turista hace un prepago de la luz que va a consumir, al final de la estancia, se hace un proceso de vaciado del contador de luz prepago hacia la Tarjeta Chip que posteriormente se lee mediante el Software de Control, de esta forma se le devuelve al cliente el importe correspondiente a la energía no consumida. Todo esto lo controla la administración través de un lector de tarjetas y de un sencillo software, que son parte del sistema.\r\n\nAhora el gasto de electricidad puede ser controlado por el inquilino, el cual se esforzará por reducirlo porque le afecta directamente, le damos la información para que sea responsable y siga comprometido como si estuviera en su domicilio habitual, solo pagará lo que consuma. \n\n Esta instalación no interfiere con la compañía de suministro eléctrico, es totalmente legal y no infringe ninguna normativa vigente de Baja Tensión.","caracteristicas":[],"opciones":[],"imagenes":["../tienda/img/p/6/4/64.jpg","../tienda/img/p/6/5/65.jpg","../tienda/img/p/6/6/66.jpg"],"ficha":"index.php?producto=27"},{"id":30,"nombre":"Pack Kit Básico 10-apartamentos","referencia":"","resumen":"El pack incluye:\n\r\n\r\n10 Contadores Prepago\n\r\n1 Lector / Grabador con software\n\r\n12 Tarjetas chip","descripcion":"El sistema es sencillo y de rápida implementación:  \n\n\r\nSe instala un Contador Prepago (entiéndase contador de luz prepago), en la entrada del tablero eléctrico de cada apartamento que se desee controlar. \n\n El contador prepago “Lee” la información que se le suministra mediante una Tarjeta Chip e indica en todo momento la electricidad que se ha consumido y la disponible, en ese apartamento en particular, además permite programar una señal de alarma que avisa con mucha antelación que se debe recargar para no perder el suministro. \n\nSi llegado el caso, el consumo “cargado” se agota, el contador de luz prepago corta el servicio eléctrico. \n\nPara que esto no suceda, se debe “recargar” la tarjeta Chip con más saldo (pre-pagando a la administración) y con esto se recarga el contador de luz prepago, las veces que haga falta. \n\nComo el turista hace un prepago de la luz que va a consumir, al final de la estancia, se hace un proceso de vaciado del contador de luz prepago hacia la Tarjeta Chip que posteriormente se lee mediante el Software de Control, de esta forma se le devuelve al cliente el importe correspondiente a la energía no consumida. Todo esto lo controla la administración través de un lector de tarjetas y de un sencillo software, que son parte del sistema.\r\n\nAhora el gasto de electricidad puede ser controlado por el inquilino, el cual se esforzará por reducirlo porque le afecta directamente, le damos la información para que sea responsable y siga comprometido como si estuviera en su domicilio habitual, solo pagará lo que consuma. \n\n Esta instalación no interfiere con la compañía de suministro eléctrico, es totalmente legal y no infringe ninguna normativa vigente de Baja Tensión.","caracteristicas":[],"opciones":[],"imagenes":["../tienda/img/p/8/0/80.jpg","../tienda/img/p/7/7/77.jpg","../tienda/img/p/7/8/78.jpg"],"ficha":"index.php?producto=30"},{"id":28,"nombre":"Pack Kit Básico 3-apartamentos","referencia":"","resumen":"El pack incluye:\n\r\n\r\n3 Contadores Prepago\n\r\n1 Lector / Grabador con software\n\r\n5 Tarjetas chip","descripcion":"El sistema es sencillo y de rápida implementación:  \n\n\r\nSe instala un Contador Prepago (entiéndase contador de luz prepago), en la entrada del tablero eléctrico de cada apartamento que se desee controlar. \n\n El contador prepago “Lee” la información que se le suministra mediante una Tarjeta Chip e indica en todo momento la electricidad que se ha consumido y la disponible, en ese apartamento en particular, además permite programar una señal de alarma que avisa con mucha antelación que se debe recargar para no perder el suministro. \n\nSi llegado el caso, el consumo “cargado” se agota, el contador de luz prepago corta el servicio eléctrico. \n\nPara que esto no suceda, se debe “recargar” la tarjeta Chip con más saldo (pre-pagando a la administración) y con esto se recarga el contador de luz prepago, las veces que haga falta. \n\nComo el turista hace un prepago de la luz que va a consumir, al final de la estancia, se hace un proceso de vaciado del contador de luz prepago hacia la Tarjeta Chip que posteriormente se lee mediante el Software de Control, de esta forma se le devuelve al cliente el importe correspondiente a la energía no consumida. Todo esto lo controla la administración través de un lector de tarjetas y de un sencillo software, que son parte del sistema.\r\n\nAhora el gasto de electricidad puede ser controlado por el inquilino, el cual se esforzará por reducirlo porque le afecta directamente, le damos la información para que sea responsable y siga comprometido como si estuviera en su domicilio habitual, solo pagará lo que consuma. \n\n Esta instalación no interfiere con la compañía de suministro eléctrico, es totalmente legal y no infringe ninguna normativa vigente de Baja Tensión.","caracteristicas":[],"opciones":[],"imagenes":["../tienda/img/p/7/0/70.jpg","../tienda/img/p/6/8/68.jpg","../tienda/img/p/6/9/69.jpg"],"ficha":"index.php?producto=28"},{"id":29,"nombre":"Pack Kit Básico 5-apartamentos","referencia":"","resumen":"El pack incluye:\n\r\n\r\n5 Contadores Prepago\n\r\n1 Lector / Grabador con software\n\r\n10 Tarjetas chip","descripcion":"El sistema es sencillo y de rápida implementación:  \n\n\r\nSe instala un Contador Prepago (entiéndase contador de luz prepago), en la entrada del tablero eléctrico de cada apartamento que se desee controlar. \n\n El contador prepago “Lee” la información que se le suministra mediante una Tarjeta Chip e indica en todo momento la electricidad que se ha consumido y la disponible, en ese apartamento en particular, además permite programar una señal de alarma que avisa con mucha antelación que se debe recargar para no perder el suministro. \n\nSi llegado el caso, el consumo “cargado” se agota, el contador de luz prepago corta el servicio eléctrico. \n\nPara que esto no suceda, se debe “recargar” la tarjeta Chip con más saldo (pre-pagando a la administración) y con esto se recarga el contador de luz prepago, las veces que haga falta. \n\nComo el turista hace un prepago de la luz que va a consumir, al final de la estancia, se hace un proceso de vaciado del contador de luz prepago hacia la Tarjeta Chip que posteriormente se lee mediante el Software de Control, de esta forma se le devuelve al cliente el importe correspondiente a la energía no consumida. Todo esto lo controla la administración través de un lector de tarjetas y de un sencillo software, que son parte del sistema.\r\n\nAhora el gasto de electricidad puede ser controlado por el inquilino, el cual se esforzará por reducirlo porque le afecta directamente, le damos la información para que sea responsable y siga comprometido como si estuviera en su domicilio habitual, solo pagará lo que consuma. \n\n Esta instalación no interfiere con la compañía de suministro eléctrico, es totalmente legal y no infringe ninguna normativa vigente de Baja Tensión.","caracteristicas":[],"opciones":[],"imagenes":["../tienda/img/p/8/1/81.jpg","../tienda/img/p/7/1/71.jpg","../tienda/img/p/7/2/72.jpg"],"ficha":"index.php?producto=29"},{"id":32,"nombre":"Pago directo","referencia":"","resumen":"De acuerdo con la administración","descripcion":"","caracteristicas":[],"opciones":[],"imagenes":["../tienda/img/p/8/3/83.jpg"],"ficha":"index.php?producto=32"},{"id":26,"nombre":"Programador de tarjetas teclado","referencia":"","resumen":"Lector grabador con teclado incorporado.","descripcion":"El lector grabador con teclado es un dispositivo que lee y graba las tarjetas chip de manera autónoma, no necesita conectarse al ordenador. A través del mismo, las tarjetas son cargadas con un determinado saldo y al final de la estancia se leen para devolver al cliente el saldo no consumido.","caracteristicas":[],"opciones":[],"imagenes":["../tienda/img/p/6/3/63.jpg"],"ficha":"index.php?producto=26"},{"id":25,"nombre":"Programador tarjetas chip","referencia":"PUTCH","resumen":"Programador universal de tarjetas chip. Lector / grabador mediante software de control","descripcion":"","caracteristicas":[],"opciones":[],"imagenes":["../tienda/img/p/6/2/62.jpg"],"ficha":"index.php?producto=25"},{"id":31,"nombre":"Tarjeta Chip","referencia":"","resumen":"Tarjeta chip para la recarga de los contadores prepago. El precio es por unidad.","descripcion":"","caracteristicas":[],"opciones":[],"imagenes":["../tienda/img/p/8/2/82.jpg"],"ficha":"index.php?producto=31"}]}